Clean patch work sized to the damage, floated out so the repair disappears.
Patching is the everyday work of this trade, and the whole craft of it comes down to one judgment call made before any tool comes out: how big does this repair need to be?
Get that call right and the patch disappears. Get it wrong — almost always by going too small — and you get a repair that either cracks at the edges or shows as a soft rectangle in raking light forever.
The instinct is to make the repair as small as the damage. It feels tidier and it feels cheaper. It is usually wrong, for a reason that is easy to miss: the visible damage and the actual damage are different sizes.
If the core is intact and it is just a surface dent, that fills and floats. No cutting. Genuinely small stuff.
These need backing behind them. The damage is squared up, cut past any crushed or delaminated paper, backed, patched, and floated well past the edge. See our hole repair page for the detail on the common types.
Past a certain size a cut-in piece landed on studs beats a backed patch — it is more stable and it is honestly faster. The seams get taped like any other joint.
If the board is compromised across a wide area — water damage, crumbling, damage in several spots on one sheet — patching stops making sense and replacing the sheet is faster, cheaper, and holds better. We will tell you which one you have rather than patching something that wants replacing.
Worth knowing, because it changes what is worth paying for.
Raking light finds everything. A wall with a window along its length is lit at a low angle all day, and that angle turns any ridge or texture edge into a shadow. Patches on those walls have to be genuinely right.
Flat light forgives. An interior wall lit by a ceiling fixture is far more tolerant. The same patch that would be obvious across from a window can be effectively invisible here.
Ceilings are the worst case. Nothing to hide behind and raking light all day. It is why ceiling work gets floated wider than the identical repair on a wall.
Hallways are close quarters. Narrow means you see the wall from two feet away rather than ten, and everything is more visible at two feet.
Three things scope a patch in about a minute: roughly how big, roughly where in the room, and what the texture is — smooth, orange peel, knockdown, or popcorn. If you do not know the texture, a photo answers it instantly and usually settles the price too.
Also useful: whether anything above or behind that spot has ever leaked, and whether the house is old enough that the texture might be hand-applied.
A large share of our patching is not homeowners at all — it is landlords and property managers with a unit that has to be rent-ready, and sellers with a house going on the market.
That work is repeatable and we are set up for it. Give us the unit count and the actual deadline on the phone. If the deadline does not work we will say so then, rather than discovering it together on the day.
And we will tell you which repairs will not change your listing photos. That conversation costs us line items and we would still rather have it.
The list is short and the edges matter.
We do not paint. We repair and texture; the painting is yours or your painter's. We do not remodel, frame, or add on. We do not do foundation work, plumbing, roofing, or mold remediation.
When a repair needs one of those first — a live leak above the damage, significant growth in the cavity, movement that a foundation company should look at — we will tell you and wait rather than patch over it. A repair that fails is worse for us than a job we never took.
If you are painting anyway, get the patching done first — and tell your painter that is the plan.
The reason is sheen. A patch introduces new compound and new texture into a wall whose paint has been sitting there for years, fading fractionally and collecting a surface of its own. Even a flawless patch under a fresh spot of touch-up paint can read slightly different, because the touch-up is newer than everything around it.
Painting the wall corner to corner after the repair erases that entirely. It is the cheapest way to make a good repair look perfect, and it costs nothing extra if you were painting regardless.
The reverse order is the expensive one: paint the room, then discover the patches you meant to do, then touch up over fresh paint and watch the touch-ups show.
Every patch that shows, shows for the same reason: the compound stopped too soon.
Think about what you are actually building. The patch area is slightly proud of the surrounding wall — you have new compound sitting on top of existing surface. That transition has to be spread out over enough distance that the eye and the light cannot find where it starts. Stop it four inches out and you have built a low, wide bump with a defined edge. That edge catches light and throws a shadow, and once you notice it, it is all you see.
Float wide, in thin coats, and let each one dry. That is the whole secret and it is not a secret at all — it is just slower than most people want to be. It is also why a patch that takes twenty minutes to fill takes two visits to finish properly when it needs three coats.
Homeowners, obviously — the wall got damaged, they want it to look like it did not.
But a large share of our patch work is turn work. Landlords and property managers with a unit that needs to be rent-ready, where a wall full of anchor holes and a doorknob punch is between them and listing photos. That work is straightforward, it is repeatable, and we are set up for it.
And pre-sale prep, where a house is going on the market and every visible patch is a thing a buyer's eye stops on.
Frisco grew fast and recently, and that shapes every drywall call we take here.
The housing stock is young. Most of what we walk into went up in the last couple of decades, which means we are rarely dealing with forty years of accumulated seasonal movement. What we are dealing with instead is homes still finding their level — first-generation settlement, working itself out through drywall that has not had to move much yet.
our patching service covers this in detail. And if you have other drywall damage in the same visit, tell us on the phone — multiple repairs done together are more efficient than one at a time, because the mud coats dry in parallel.
For the full picture of what we handle locally, see our crew in Frisco.
Tell us what happened and roughly how big the area is. A photo texted over usually settles the scope in a minute.
You get the scope and the number before we start. Patch versus sheet replacement, texture type, and how many coats it needs.
We cut, hang, tape, float, and match texture, then clean the space. Most single-room repairs are done inside one visit.
Based in Plano, covering Frisco across the North Dallas metro. Text a photo for a free virtual estimate, or call and describe the damage.
Our pricing starts at $300 for any job, however small. Beyond that it depends on the size of the damage, the texture that has to be matched, and how many coats the finish needs. Text a photo to (972) 469-5046 for a free virtual estimate and we will give you a real number, not a placeholder range.
Virtual estimates are free — text or email a photo and we will come back with a real number, no charge and no obligation. In-person estimates are $100, credited back against your job when you book with us. For most repairs a clear photo is all we need.
Most single-room repairs are handled in one visit. Larger areas, or repairs that need multiple mud coats to dry properly, can run into a second day. We tell you which one you are looking at up front.
Yes. Matching the surrounding texture is part of the repair, not an add-on. A flat patch with the wrong texture still reads as a repair.
Yes. Frisco is inside our service area. Call (972) 469-5046 to get on the schedule.
Roughly, anything past an inch or two. Below that you are filling a dent. Above it, compound alone has nothing to hold onto and will eventually crack out. The exact line depends on the location and what is behind the wall.
Almost always because it was not floated wide enough. The compound stopped abruptly and left an edge, and that edge catches light. The fix is to float it back out properly — which usually means going over a repair someone already did.
